Sdi Permite Capsules Spill 2

Composition

Ag 56%, Sn 27.9%, Cu 15.4%, In 0.5%, Zn 0.2% (Contains zinc in an alloyed form, not free zinc)

Warnings

• Harmful if vapours are inhaled.
• Avoid breathing vapours.
• Harmful if swallowed.
• Use with adequate ventilation
• Single-use only
• For professional use only

CAUTION: Federal law restricts this device to sale by or on the order of a dentist.

• Keep out of reach of children 
• Do not open capsules prior to trituration
• Do not remove the coloured plunger from the capsule.
• Effect of mercury on metals: Mercury reacts with and embrittles particular metals and their alloys. Avoid unnecessary contact between mercury and those metals (and their alloys).
• The wearing of gloves, glasses and protective clothing is recommended for all dental procedures
• Do not eat, drink or smoke when using this product
• Follow good safety clinical practices when performing amalgam restorations.
• Always keep unused product in original, labelled container and store in temperatures below 25°C / 77°F in a cool, well-ventilated area.
• Existing studies indicate that some people with amalgam restorations may be sensitive to prolonged close encounter with sources of electromagnetic radiation, ie mobile phone. In patients hypersensitive to amalgam, existing amalgam restorations should be replaced with an alternative material.
• Some patients may experience a metallic taste post restoration especially when placed in close contact with other metal restorations due to galvanic effect. If this persists, consider replacing with an alternative material.
• Dispose of used capsules in accordance to national regulations.

Packaging

• Box of 50 Capsules

Direction of use

STEP 1:

• Isolate tooth.

STEP 2:

• Prepare cavity using standard technique for amalgam restoration.

Note: In cases where pulp protection is necessary, use a calcium hydroxide liner or glass ionomer cement.

STEP 3:

• Activate a capsule on a bench or hard surface until plunger is fully flushed with the body of the capsule.

 

 

STEP 4:

• Place activated capsule in a high speed multi-use triturator.

STEP 5:

• Triturate capsule as per recommended in Table below.

 Mechanical Amalgamation Mixing Time Requirement:

Amalgamator	Speed	Permite
Ultramat 2 (SDI Ltd.)	Fixed (4600 rpm)	1, 2 & 3 spill	5 spill
		8 ± 1 sec	6 ± 1 sec
Ultramat 2 (SDI Ltd.)	Fixed (450 rpm)	1, 2 & 3 spill	5 spill
		8 ± 1 sec	6 ± 1 sec

STEP 6:

• Carefully remove the triturated capsule from the triturator and gently tap the base on a bench or hard surface once.

STEP 7:

• Open the capsule by removing the base from the body to access the prepared amalgam.

Note: Freshly mixed amalgam should have a bright look and a plastic consistency.

STEP 8:

• Immediately insert amalgam into prepared cavity using a clean amalgam carrier employing standard amalgam condensation technique.

Note:

• i. ?If moisture is introduced into the dental amalgam before it has set, properties such as strength and corrosion resistance can be affected adversely. If the alloy contains zinc, such contamination can result in excessive expansion (delayed expansion). Use a dry field, whenever it is possible.
• ii. Permite contains zinc in an alloyed form and not free zinc. It?s the free zinc which is very sensitive to moisture.

STEP 9:

• Remove any mercury rich amalgam from the surface that may develop during condensation.

STEP 10:

• Trimming and carving can begin after condensation using a sharp carver.

STEP 11:

• Light burnishing can be carried out after 24 hours to improve surface smoothness. Avoid over heating by ensuring adequate water cooling and low speed.