GC G – CEM One Paste Pak – Starter Kit (Translucent)

Features

Description

G-CEM ONE Paste Pak, the new self-adhesive resin cement from GC simplifies all cementation procedures.G-CEM ONE Paste Pakbrings together high bond strength, effortless clean-up and long-lasting aesthetics as well as an excellent self-curing ability for a wide range of indications in ONE product solution.

G-CEM ONE Paste Pakis a truly universal, non-technique sensitive, versatile and reliable product that gives the flexibility of being effective in all cementation procedures for any type of restorations; from metal-based to resin and all-ceramic inlays, onlays, crowns, bridges, and posts. It demonstrates excellent bond strength to enamel, dentin and all indirect restorations.

In addition, the optionalAdhesive Enhancing Primer (AEP)and its innovative GC Touch Cure feature provides optimal bond strength in challenging clinical situations, such as low retentive surfaces. The chemical initiator in the AEP accelerates the chemical cure of the cement to ensure optimal bonding. The AEP is easy to apply; no additional light-curing is needed apply and air-dry.

Indications :

• Cementation of all types of all ceramic, resin and metal-based inlays, onlays, crowns and bridges.
• Cementation of metal, ceramic, fiber posts, and cast post and cores.
• Cementation of all ceramic and composite veneers.
• Final cementation of crowns and bridges on implant abutments.

Key Specifications

• Mixing Time (sec.) -10”
• Working Time (23?C3?F) (min., sec.) – 2’30”
  (from start of mixing)
• Finishing Time (37?C9?F, after excess cement removal) (min., sec.) – 4’00”

Packaging

GC G-CEM One Paste Pak – Starter kit (Translucent):

• 1 x G-CEM ONE Paste Pak Cartridge (7.6 mL)
• 1x G-CEM ONE ADHESIVE ENHANCING PRIMER (2 mL)
• Mixing Pad (No.22)

Direction of use

APPLICATION OF G-CEM ONE ADHESIVE ENHANCING PRIMER
(Optional) –
a) Dispense a few drops into a clean dispensing dish. Close the bottle
cap immediately.
b) IMMEDIATELY apply to the prepared enamel and dentin surfaces
using the disposable applicator.
c) Leave undisturbed for 10 seconds after the end of application.
d) Dry thoroughly for 5 seconds with oil free air under MAXIMUM air
pressure. Use vacuum suction to prevent splatter of the adhesive.

RESTORATION PREPARATION –
Make sure that the restoration is pretreated and handled according to
the manufacturer instructions.
a) For Glass Ceramics, hybrid ceramics and composite, apply a silane
coupling agent to the bonding surface,and dry with an air syringe.

DISPENSING –
a) Remove the cartridge cover
b) Depress the lever to dispense the required amounts of paste onto the
mixing pad.
NOTE:
1. Before dispensing the first time from a new cartridge or after a long
interval in between use, bleed the pastes from the cartridge.
2. The adjusting guide can be moved forwards or backwards to change
the quantity of material to be dispensed.
1. Position of adjusting guide for one inlay.
2. Position of adjusting guide for one crown.
c) While depressing the lever, level and cut off the extruded material from the cartridge tips by moving the cartridge and dispenser to an upright position on the mixing pad
d) When the lever is released after dispensing, residual pastes at the
cartridge tips are retracted into the cartridge. Clean the cartridge tip
and replace the cartridge cover.
NOTE:
1. The amount of residual material in the cartridge can be confirmed by
the position of the sliding block on the underside of the dispenser.

MIXING
After dispensing, spread the two pastes thinly on the mixing pad using
a plastic spatula. Mix thoroughly, with lapping strokes, for 10 seconds.
Be careful not to incorporate air bubbles.

CEMENTATION
a) Coat the internal surface of the restoration with sufficient cement
and seat immediately. The working time is 2 minutes 30 seconds
from start of mix at 23?C (73?F). Higher temperatures will shorten
the working time