Zhermack Zetaplus Putty Impression Material
$ 10.00 – $ 55.00
High initial flowability, Green colour, Spearmint flavour, Reduces mucous compression in the phase of insertion in the oral cavity, Excellent hardness after setting, In the two-stage technique, it acts perfectly as a special tray, In double mixing, it adapts to the consistency of low viscosity fluid, Variable working and setting times according to catalyst quantity (Indurent gel)
| Quantity | Price |
|---|---|
| 2 - 5 | $ 9.90 |
| 6 - 10 | $ 9.80 |
| 11 - 20 | $ 9.60 |
| 21 - 50 | $ 9.50 |
| 51 + | $ 9.30 |
Features
- High initial flowability
- Green colour
- Spearmint flavour
- Reduces mucous compression in the phase of insertion in the oral cavity
- Excellent hardness after setting
- In the two-stage technique, it acts perfectly as a special tray
- In double mixing, it adapts to the consistency of low-viscosity fluid
- Variable working and setting times according to catalyst quantity (Indurent gel)
Description
REDUCED MARGIN OF ERROR
- Clear colour contrast reduces the risk of error, consequently saving time and material.
BALANCED REACTIVITY
- Ideal balance between working time and setting time. (Snap-set effect).
- The optimal dosage of the catalyst increases the available working time and reduces the contraction
“FLOW CONDITIONING” EFFECT
- Increased flowability and extreme dimensional stability are achieved thanks to SAS (Synthetic Amorphous Silicas) high-activity spheroid fillers.
Key Specifications
| ISO 4823 – ADA 19 | Type Putty Consistency |
| Mixing time | 30” |
| Total working time?23?/73?) | 1′ 15” |
| Time in mouth | 3′ 15” |
| Setting time?23?/73?) | 4′ 30” |
| Compressive deformation (min-max) | 2 -5 % |
| Elastic recovery | >98% |
| Dimensional stability (after 24 h) | <-0.2% |
Packaging
Zhermack Zetaplus C Silicone Intro Kit
- 1 x 900ml Putty 1x60ml Catalyst Tube 140ml Light Body
Zhermack Zetaplus Indurent Catalyst Gel
- 1 x 60ml Catalyst Tube
Zhermack Zetaplus C Silicone Impression Material Putty
- 1 x 900ml Putty
Zhermack Zetaplus Light Body
- 1 x 140ml Light Body
Zetaplus Bucket 10KG
- 1 x 10kg Bucket of Putty Only
Direction to Use
USE
Zetaplus: Polysiloxane for the first impression characterized by initial flow in the working phase and high rigidity after hardening. Recommended for the two-stage technique (double impression).
Zetaplus Soft: Polysiloxane for the first impression characterized by initial flow in the working phase and adequate elasticity on removal from the oral cavity. Recommended for the two-stage technique (double impression).
Oranwash VL: Low viscosity, extremely fluid, hydro-compatible, polysiloxane. Recommended for the two-stage technique (double impression).
Oranwash L: Low viscosity, extremely fluid, hydro-compatible, polysiloxane. Recommended for the two-stage technique (double impression).
Thixoflex M: Low viscosity, thixotropic, hydro-compatible, polysiloxane. It does not drip when injected directly into the preparation, yet flows easily. Recommended for the two-stage technique (double impression) and a single phase (simultaneous) and for the relining of removable prosthesis.
ZETAPLUS / ZETAPLUS SOFT – INSTRUCTIONS FOR USE
Dosage: Use the measuring spoon to dose the required quantity of Zetaplus and spread it out over your hand (note: for the correct dosage the putty should be level with the top of the measuring scoop). Press the rim of the measuring scoop onto the putty once for each measure dosed. For each measure of material, apply two strips of Zhermack Indurent Gel as long as the measuring scoop (4 cm.)
Mixing:
- Fold and knead the putty energetically with your fingertips for about 30 sec., until the colour is even, without any stripes
- Spread out the putty over the impression tray. The working time including mixing time is about 1 min. 15 sec.
- Put into the mouth and wait until it is set, which will take about 3 min. 15 sec.
ORANWASH VL / ORANWASH L / THIXOFLEX M – INSTRUCTIONS FOR USE
Dosage: Extrude the required quantity, observing the dosage scale on the mixing block. Then dose a quantity of Zhermack Indurent Gel equal to the length of the fluid. When using Zhermack Indurent Liquid, dose one drop of hardening liquid for each notch of fluid.
Mixing:
- Mix energetically with the spatula, and then carefully spread the mixture out, pressing it over the mixing block to eliminate any air which may have been incorporated into the mixture. Repeat this operation until the mix is even in color.
- Mixing time should ideally be about 30 sec.
- Apply the mixture to the impression tray with a spatula or a syringe for elastomers.
- The working time of c-silicones including mixing time is about 1 min. 30 sec.
- Put into the oral cavity and wait for the mix to harden, which will take about 3 min. 30 sec.
1. We offer Worldwide Shipping by Courier via Air or Sea mode.
2. Product will be dispatched within 5-7 working days.
3. Delivery will take a maximum of 7-15 days, based on the shipping option you choose.
4. Kindly check customs restrictions and rules in your country for specific products, mostly 99% shipments are cleared and delivered smoothly.
5. For Bulk inquiries or customized manufacturing please contact us.
Product Enquiry
Related Products
Features:
3M Cavit G Temporary Filling Material
Volume: 28g
Quick & Void-free Curing
Completely Removable without Burs
Simple to Apply
Features:
3M Adper Easy Bond Dental Adhesive
Features:
3M Cavilon No Sting Barrier Film Wipe
Volume: 1 ml
Type: Wipe
Box of 25
Alcohol free
Features:
3M Clinpro Dental Sealant
Long-lasting Protection Against Caries
Colour Change Technology
Low Viscosity
Bonds to Enamel
Features:
3M Charger Stand for Surgical Clipper – 9683
Charger Stand
Excellent performance
Reduces the risk of infection
Superior design